Now booking free roof inspections in Pinellas ParkRoof Copilot License · CCC1336568

Tile Roofing in Pinellas Park, FL:
Keep the Good Tile, Renew What Sits Under It.

Tile roofing in Pinellas Park for concrete and clay tile homes. On a lot of tile roofs the tile still has years in it while the underlayment below has given out, so the usual job is to lift the tile, put down new underlayment and set the sound pieces back. Our workmanship carries a 15-year written warranty on top of the manufacturer's.

15-year workmanship warranty in writing, plus the manufacturer's coverage
Every slope measured from high-resolution imagery before the visit
Photos of the new underlayment in your portal before tile covers it
Licensed & insured
Roof Copilot · CCC1336568
Get your free roof quote
$0 · NO OBLIGATION

Takes about 30 seconds. A local roofing specialist follows up the same business day.

What do you need?

We never sell your info 30 seconds Licensed & insured
Step 2 shows your roof from above with its size and pitch, before anyone visits.
15
Year warrantyWorkmanship, in writing
FL Lic. CCC1336568Licensed & insured
$0
InspectionNo pressure, ever
4,023Pinellas Park homes built in 2000 or later (2020 to 2024 Census estimates)
Dry InThe roof inspection the city requires before tile goes back on
10 daysBusiness days the city says most permits take once paperwork is complete
15 yearsOur written workmanship warranty

Tile Roofing in Pinellas Park: Where It Shows Up

Most of Pinellas Park was built in the 1970s and 1980s, and most of those houses wear shingle or metal today. Tile shows up on a share of the newer homes: Census estimates for 2020 to 2024 count 4,023 Pinellas Park homes built in 2000 or later, plus another 2,056 from the 1990s. You’ll also find it on older houses where an owner chose tile at a past re-roof.

So this page is for the house that has tile now, or the owner thinking about it. If yours is shingle, our architectural shingle page covers that work. If you need a whole new roof of any kind, start with roof replacement.

What matters on a tile roof is different from a shingle roof. The surface you see from the street is rarely the part that fails.

Concrete tile roof on a Florida home
Tile sits on a share of the city's newer houses next to shingle and metal

Concrete or Clay: Tile Roofing in Pinellas Park by Material

Residential tile comes in two main materials, and they behave differently on the roof.

Concrete tile is cast from cement and sand, comes in flat, S-shaped and barrel profiles, and is heavy per piece. It handles foot traffic better than clay, and replacement pieces in a similar shape are easier to find.

Clay tile is fired, like pottery. It tends to show up as a barrel profile on Spanish-style houses. Clay holds its color well and is lighter per piece than concrete, but it cracks more easily under a boot, and an older clay color can be hard to match years later.

Either material sheds rain and takes the sun for a long time. Neither one keeps the house dry by itself. That job belongs to the layer underneath.

Concrete and Clay, Side by Side

  • Concrete tileHeavier per piece, tougher to walk on, made in flat, S and barrel shapes
  • Clay tileFired, brittle underfoot, holds its color, often a barrel shape
  • MatchingConcrete profiles are easier to find; an older clay color can be hard to match
  • BothShed rain and take the sun, but neither one is the waterproof layer

The Layer Under the Tile Does the Real Work

Think of a tile roof as two roofs. The top one, the tile, breaks up the rain, blocks the sun and carries most of the water down the slope. The bottom one, the underlayment, is the true waterproof sheet. Every tile roof lets some water slip between the laps, more so when wind drives rain sideways during a summer storm. That water runs down the underlayment and drains at the eave.

Pinellas Park gets about 49 inches of rain a year, going by ERA5 model data for the city. Every one of those inches lands on the tile, and a share of it lands on the underlayment too. Add the attic heat cooking that layer from below, and it is easy to see why the underlayment usually gives out before the tile does.

When the underlayment cracks, shrinks or tears, water that used to drain away reaches the deck instead. The tile above can look perfect the whole time. That is why a ceiling stain under an unbroken tile roof is so common. For a single active leak, our roof leak repair page explains how we trace it and stop it.

1 · Tile sheds most of the rain2 · Water that gets past itruns down the underlaymentThe underlayment does the real waterproofing
Rain that slips between tiles runs down the underlayment and out at the eave

Lift, Re-Lay and Reset: The Usual Tile Job

Because the tile often outlasts the layer beneath it, a lot of tile work in Pinellas Park is not a new tile roof at all. It is a reset.

Here is how it typically goes. We lift the tile by hand, row by row, and stack the sound pieces on the roof. Old underlayment and worn flashing come off. The deck is checked, bad wood replaced, and the sheathing re-nailed. New underlayment goes down, with new flashing at valleys, walls, pipes and edges. Then the same tile goes back on, with new pieces in place of any that cracked.

Not every roof needs the full treatment. Sometimes one slope or one valley has failed and the rest is fine, so only that area comes up. Sometimes the tile itself is soft, faded or too broken to save, and new tile is the better answer. The free inspection tells us which one you have, and the photos show you why.

A reset usually costs less than a brand-new tile roof, since the tile is the expensive part and you already own it.

04Decking, rottedwood replaced03Peel and stickunderlayment02Flashing, pipeboots, drip edge01Matched shinglesand ridge caps
Deck, underlayment, flashing, then tile on top

Fixing Cracked and Slipped Tile

Not every tile problem means lifting a whole slope. A branch drops on the roof. A satellite installer steps in the wrong place. A ridge tile works loose after years of wind. These are spot repairs, and they are ordinary roof repair.

The work is careful more than complicated. We take out the broken piece without disturbing its neighbors, look at the underlayment it was covering, and set in a replacement that matches as closely as current products allow. If the exact color isn’t made anymore, original tile from a hidden back slope can move to the front, and the new piece goes where nobody will see it.

Cracked tile is a small fix that gets bigger if left alone. Each open crack sends rain straight to the underlayment at one spot, and if that layer was already tired, the leak follows.

We also watch where we walk. On tile, we step on the lower part of each piece, where it rests on the course below, and keep off barrel tops and the middle of a span. We bring spares so anything that cracks under us is replaced before we leave.

Small Tile Problems Worth Fixing Early

  • A cracked piece mid-slopeSwapped for a matching tile, with the underlayment checked below it
  • A slipped tileReset and fastened so the course lines up again
  • Loose ridge or hipRe-bedded or re-fastened along the run
  • Rusted flashingReplaced at walls, valleys and pipes while the tile is up

How Tile Is Held Down

Tile is heavy, and that weight helps, but it is not what keeps a tile on in a Gulf storm. Each tile is attached. Depending on the product and the wind design for the house, tile is fastened with nails or screws, set in an approved foam adhesive, or a mix of the two. Ridge and hip tile get their own attachment along the top of the roof.

Wind pulls hardest at the eaves, rakes, hips and ridges. Those are the spots where we see slipped and missing tile after a storm, and where we pay the most attention on a reset. When tile goes back on, it is attached the way its product approval calls for, not the way the last crew happened to do it.

After a storm, look from the ground. Pieces of tile in the yard, a gap along the ridge or a row that sits crooked are worth a call. Our storm damage roof repair page covers that work. You get a documented photo report of the damage to share with your insurer, and the claim itself stays between you and them.

RidgeEaveEave
Edges, hips and ridges take the most uplift, so fastening matters most there

Tile Weight and the Deck

Tile is one of the heaviest roof coverings on a house. A home that has always had tile was framed for it. Questions come up when the material changes, or when the deck underneath has aged.

On a reset, the deck is uncovered for the first time in years. That is the moment to fix it. Soft or rotted sheathing is cut out and replaced, and the deck is re-nailed before any underlayment goes on. The City of Pinellas Park lists a Building Sheathing inspection (“Inspect sheathing on roof and walls and nailing”) and says roofing must have a Dry In inspection. We book them as the job reaches each stage. The city also has a Deck Attachment mitigation form that records deck fastening and the secondary water barrier; a licensed contractor, a 468 inspector, or a Florida architect or engineer can sign it.

Going from shingle or metal to tile is a heavier load. The rafters or trusses need to be checked first, sometimes by an engineer, before tile is even priced. Going the other way, from tile to something lighter, is easy on the framing.

Before tile covers anything, photos of the deck, the new underlayment and the flashing go into your homeowner portal, so you can see the layers nobody will see again.

Re-roof in progress on a Florida home with the deck exposed
With the tile stacked, the deck gets checked and re-nailed before new underlayment

Partial Tile Work and the 25% Rule

Florida’s Existing Building Code limits how much of a roof can be patched. No more than 25% of a roof or roof section may be repaired, replaced or recovered in any 12 months unless the whole roof or section is brought up to current code.

A state law eases that rule for newer roofs. If the existing roof went on under the 2007 Florida Building Code or later, only the part being worked on has to meet current code. Local governments can’t change that.

For tile owners in Pinellas Park, the date the current roof went on is the question to answer before planning a partial reset. A tile roof installed in the 2000s or later may fall under the easier rule. An older one may not. We look at the permit history and tell you which side of the line your roof sits on.

When Tile Repair Becomes a Whole-Roof Job

Under 25%The repaired area is brought up to current code
25% or moreThe whole roof or section meets current code, unless the roof was done to the 2007 code or later

HOA Approval Before the Tile Comes Off

Many newer subdivisions have a homeowners association, and many associations have roof rules. Some require tile. Some name approved colors or profiles. Some allow metal or shingle with board approval. The rules come from your association’s documents, not from the city.

If you live in an HOA, get approval before work starts. A like-for-like reset with your own tile usually raises few questions, since nothing changes from the street. A new tile color or a switch to another material is the kind of change boards want to review. Your quote lists the material, profile and color, which is what most boards ask for.

What an HOA Usually Wants to See

  • MaterialTile staying tile, or a request to change it
  • Profile and colorThe tile shape and color you plan to use
  • TimingApproval in hand before the work starts
  • RulesYour association's own documents decide; ask the board or manager

Moving From Tile to Metal or Shingle

Some owners decide tile isn’t worth keeping. Maybe the tile is worn out, or the owner wants a lighter roof.

Standing seam metal is much lighter than tile, holds up well at the edges in wind, and looks quite different from the street. Architectural shingle costs the least upfront and has the shortest life of the three. Staying with tile costs the most upfront on most homes, but when the old tile can be reused, a reset closes much of that gap.

Your quote comes as Good, Better and Best options, so a reset, new tile and a metal roof can sit next to each other. Each option is signed from your phone, and the price is locked once we send it. Monthly payment options are available. There are no prices on this page because every roof is measured first.

Leaving Tile Behind

  • Tile to standing seam metalMuch lighter on the framing, a different look from the street
  • Tile to architectural shingleLowest upfront of the three, shortest life
  • Tile back on tileSame weight, same look, often the old tile reused
Good, Better and Best can put two materials next to each other

City Permit or County Permit

A Pinellas Park mailing address doesn’t settle who issues the permit. The city grew by voluntary annexation, so pockets of unincorporated county land remain inside and around it.

Inside city limits, the Building Development Division permits the roof. The city says most applications are reviewed and issued within 10 business days once all the paperwork is in. On unincorporated land, Pinellas County Building & Development Review Services issues it instead. To see which applies to your house, look up the parcel on pcpao.gov. Either way, we pull the permit in our name and book the inspections, so you don’t have to work out which office to call.

Just south of the city, Lealman is unincorporated, so a tile roof there goes through the county. We also work in Kenneth City and Seminole, and we confirm the right office at the start.

Who Issues Your Tile Permit

Inside city limits
Building Development Division, 6051 78th Avenue N, (727) 369-5647
Unincorporated land
Pinellas County Building & Development Review Services, (727) 464-3888
City inspections
Building Sheathing and Dry In, booked a working day ahead

Tile Roofs in a Pinellas Park Flood Zone

FEMA maps show Zone AE, Zone A and Zone AH areas in or touching Pinellas Park city limits. In those areas, the city uses a 50% rule. When repairs or improvements cost 50% or more of the building’s market value, the whole building has to meet current flood standards. The city counts that per permit, not added up from one permit to the next.

A tile reset alone rarely comes near that line. A tile roof plus other storm repairs on the same permit might. We check before you sign, so the roof doesn’t surprise you.

Tile Work in a Pinellas Park Flood Zone

Under 50%The tile job goes ahead under normal permit rules
50% or moreThe building must meet current flood standards

From Address to Reset Tile: How We Run It

  1. 01

    Send Your Address

    We measure each slope, hip and ridge from high-resolution imagery before anyone comes out.

  2. 02

    Free Inspection

    We look at the tile, the ridges and the flashing, and check the underlayment and deck from the attic and under any lifted piece. You get the photos.

  3. 03

    Pick and Sign

    Spot repair, reset or full tile roof, priced side by side and signed from your phone. No pushy sales visit.

  4. 04

    Built and Covered

    We pull the Pinellas Park or county permit in our name, install a matched system bought direct from one manufacturer, book each inspection and clean up when we leave. Our 15-year workmanship warranty comes in writing, on top of the manufacturer’s.

Your homeowner portal holds the schedule, the photos of the hidden layers, the documents and your messages with us. We are a Florida certified roofing contractor, license CCC1336568, carrying liability and workers’ comp. See all our residential roofing work, or book a free roof inspection for your Pinellas Park tile roof.

Recent work

Roofs We're Proud Of

Tile roof, replaced
Tile roof, replaced
Architectural shingles, finished
Architectural shingles, finished
Standing seam metal, installed
Standing seam metal, installed
Shingle crew at work
Shingle crew at work
Whole roof replaced
Whole roof replaced
Our promise
15

Year workmanship warranty in writing, added on top of the manufacturer's warranty that covers your materials.

🧾 Permit on us

We file each permit ourselves and build every roof to the Florida Building Code. There's no form for you to fill in.

🧹 Nails picked up

The old roof leaves with us, and a magnet goes over the lawn and driveway before the crew heads out.

🛡️ Licensed with coverage

Florida certified roofing contractor CCC1336568, insured for liability and carrying workers' comp.

💳 Monthly payments

Payment options by the month mean the roof can be replaced now and the cost spread out.

Questions

Tile Roof Questions from Pinellas Park Homeowners

My Tile Isn't Broken, So Why Is the Ceiling Stained?

Most of the time the layer under the tile has failed. Some rain always gets past the tile, and the underlayment is what carries it off the roof. When that layer cracks or tears, the water reaches the wood. The fix is to lift the tile over the problem, renew the underlayment and put the tile back.

Can My Old Tile Go Back On?

Usually, when it's sound. We pull each piece by hand, look it over and stack it on the roof. Cracked or crumbling pieces are set aside and replaced. If too many are worn out, the photos will show it, and new tile becomes one of your options.

Do I Need a Permit to Fix a Few Cracked Tiles in Pinellas Park?

The city lists roof replacement and substantial roof repairs as permitted work, and storm repairs follow the same plan. We pull any permit the job needs in our name, whether the house is in the city or on county land.

Which Is Better Here, Concrete or Clay Tile?

Both work on a Florida house. Concrete is heavier and stands up better to foot traffic. Clay is lighter per piece, more brittle and keeps its color. On an existing roof, the main question is usually matching what is already there.

Will My HOA Let Me Switch from Tile to Metal?

That depends on your association's rules. Some allow only tile, some allow metal or shingle in approved colors. Get the board's approval first; your quote has the material and color details you'll need for the request.

Can I Pay for a Tile Reset Monthly?

Yes. Monthly payment options are available on tile repairs, resets and full tile roofs.

Free, no obligation

Get Your Pinellas Park Roof Measured, Free.

Enter your address. We'll handle everything else.

Or call (727) 910-1333
Call (727) 910-1333Free quote